Prototipten seri üretime, kalıptan bitmiş parçaya — İzmir'den. E-posta: info@oskakalip.com Telefon: 0506 462 17 78 WhatsApp Sohbeti Teklif Başlat
Fiyat teklifi alın

Ana Sayfa / Haberler

What Is Mold Flow Analysis? 12 Checks from Filling to Warpage

Kasım 16, 2026

Türkçe sürüm

The most expensive fault in an injection mold is the one discovered after the steel has been cut. A gate in the wrong place, air trapped in a corner or a part that warps while cooling usually means welding, re-machining and repeated trials. Mold flow analysis lets us see these problems while the mold is still on screen.

What is mold flow analysis?

Mold flow analysis (MFA) is a numerical simulation of how molten plastic moves inside a mold. The software divides the 3D part model into a mesh of small elements and, using the flow and thermal properties of the resin, calculates how the material fills the cavity, how it is packed under pressure and how it solidifies. Autodesk Moldflow and Moldex3D are among the tools widely used in the industry.

The outcome is a prediction, but with correct input data it is a very reliable guide: it shows whether filling is balanced, where weld lines and air traps will form, which areas will sink and how much the part will warp, all before the mold exists.

Flow analysis vs. DFM

The two terms are often used interchangeably, yet their scope differs.

Mold flow analysis DFM (design for manufacturability)
Scope The injection process only: filling, packing, cooling Manufacturability of the part as a whole
Method Numerical simulation Review based on design rules and experience
Topics Pressure, temperature, weld lines, air traps, shrinkage, warpage Material choice, geometry, draft, undercuts, ease of assembly and machining
Output Colour result plots and numerical values A list of recommended design changes

In short, DFM asks “can this part be made easily and economically?”, while flow analysis asks “how will this part fill in this mold?”. In a healthy project DFM comes first and flow analysis then verifies the design.

Preparation

  • Define the purpose. For a new mold the aim is to foresee risks and validate the design; for a running mold it is to solve an actual problem such as short shots or warpage.
  • Collect the data. The 3D part model, mold layout, process values and resin data are required. On the resin side this means viscosity (rheology) curves, thermal conductivity, pressure-volume-temperature (PVT) behaviour and any filler or fibre information. Accuracy depends heavily on this data.
  • Build the mesh. The mesh is the foundation. A good mesh has no free edges and no intersecting or overlapping elements, triangles are not excessively long and thin, and in dual-domain meshes the match ratio between opposite surfaces is kept high (90% or above is the usual target).

What is checked, step by step

1. Filling

How the melt fills the cavity. Filling is balanced when the flow paths reach the extremities at the same time. In practice the filling stage is set to switch over to packing when roughly 95–99% of the cavity volume is filled; switching too early leaves packing insufficient and causes sinks or unfilled areas.

2. Pressure distribution

Pressure in the cavity should be balanced and symmetric. Uneven pressure leads to different shrinkage from one area to another, and therefore to sink marks or dimensional deviation.

3. Flow front temperature

If the melt cools too much as it advances, it hesitates and forms weak weld lines; if it heats too much, it degrades. Keeping the temperature within a narrow band also lowers residual stress and warpage.

4. Clamp force

The force needed to keep the mold closed under pressure. Too little and the mold opens and flashes; far too much and the mold and machine are loaded for nothing. The value is used directly in choosing machine tonnage.

5. Shear rate and shear stress

Every resin has a shear limit. Narrow gates and fast filling can exceed it, overheating and degrading the material and marking the surface. The usual remedy is a larger gate section or an adjusted fill speed.

6. Weld lines

A weld line forms where two flow fronts meet. It is both a visible line and a zone of reduced strength. The analysis shows where it will be, and moving the gate can shift it to a hidden or unloaded area.

7. Air traps and venting

Air that cannot escape is compressed and heated, causing burn marks, unfilled corners or poor surface. The analysis shows where air will remain so vents can be placed there.

8. Shrinkage and warpage prediction

Plastic shrinks as it cools. When shrinkage is not equal in every direction and area, the part changes shape. Predicted values form the basis for the shrinkage allowance in the mold dimensions and for any geometry correction.

9. Frozen layer fraction

How much of the section has solidified. If the gate freezes early, packing pressure cannot reach the part; if thick areas freeze late, the cycle is longer. This result helps set packing and cooling times.

10. Sink mark prediction

Sinks are expected in thick sections and at the base of ribs and bosses. The analysis flags these areas in advance; thinner walls, a corrected rib ratio or higher packing are the main countermeasures.

11. Cooling

The temperature distribution on the mold surface is reviewed. Hot spots lengthen the cycle and increase warpage. The position, diameter and flow rate of the cooling channels are improved accordingly.

12. Deflection

Finally, the direction and amount of deviation after ejection is calculated. If it is outside the acceptance limit, wall thickness, gate location or cooling layout is revisited.

The three variables everything turns on

Variable Why it matters
Pressure Drives the melt to every point of the cavity. Too little causes short shots, too much causes flash.
Temperature Sets viscosity and cooling rate. Uneven distribution is the main cause of warpage and irregular shrinkage.
Cooling time The largest share of the cycle. Set correctly, it improves both output and dimensional stability.

Where it is used

  • Automotive: large, visible parts such as bumpers, instrument panels and under-hood components, to prevent sink and warpage and keep wall thickness safe under heat and load.
  • Consumer goods and packaging: containers, lids and household items, to reduce material use and cycle time and to limit flash and voids.
  • Electrical and electronics: housings, connectors and internal parts, to hold tight fit tolerances and limit warpage.

Its limits

Flow analysis is not magic. Results are only as good as the input: an analysis run with generic resin data may not fully reflect the behaviour of the actual lot. The real response of the machine, mold surface temperature and operator settings also play a part. That is why the analysis does not replace the mold trial; it lets us enter the trial knowing what to look for.

Summary

Mold flow analysis is one of the most effective ways to catch design faults before steel is cut, reduce the number of trials and bring a mold into series production sooner. At OSKA we carry out this work in-house; see our Mold Flow Analysis service page for details.

Request a Quote

Kalıp ve hassas parça işleriniz için üretim ortağınız

Kokil, plastik enjeksiyon ve alüminyum enjeksiyon kalıpları ile CNC talaşlı imalat tek atölyede. Teknik resminizi gönderin, birlikte değerlendirelim.

Bize Ulaşın
Kasım 16, 2026

Stainless Steel Grades in CNC Machining: 303, 304, 316, 420 and 17-4 PH

Devamını oku
Kasım 16, 2026

CNC İşlemede Paslanmaz Çelik Türleri: 303, 304, 316, 420 ve 17-4 PH

Devamını oku
Tüm haberler ve yazılar