Prototipten seri üretime, kalıptan bitmiş parçaya — İzmir'den. E-posta: info@oskakalip.com Telefon: 0506 462 17 78 WhatsApp Sohbeti Teklif Başlat
Fiyat teklifi alın

Ana Sayfa / Haberler

How Do Threaded Plastic Parts Leave the Mold? Thread Release Methods

Kasım 16, 2026

Türkçe

From bottle caps to luminaire glands, from filter housings to adjusting screws, many plastic parts carry a thread. A thread is an undercut relative to the mold opening direction, so how a threaded part leaves the mold is the most important design decision for the tool.

External threads

An external thread is usually the easiest case: the thread axis is laid on the parting line and the thread is cut half into each side of the mold. When the mold opens the part is free. The price is a parting line witness on both sides of the thread; where sealing or a precise fit is needed, a small flat is put on the witness line or the thread is released with a rotating element.

Five methods for internal threads

Method How it works When it fits Limit
Stripping The part flexes and is pushed off the threaded core Flexible material (PP, PE), shallow rounded threads, cap-type parts Tears the part in rigid materials and sharp threads
Unscrewing core The core rotates out of the thread, driven by motor, hydraulics or rack High volume, precise and deep threads Expensive, complex tool; the part needs anti-rotation features
Collapsible core Core segments fold inward to clear the thread Short cycles, where an unscrewing mechanism is not wanted Leaves segment witness lines; not feasible for very small diameters
Hand-loaded insert core The threaded core is ejected with the part, unscrewed by hand and put back Low volume, prototypes, limited tool budget High labour and cycle time
Tapping afterwards or metal insert The hole is molded plain; the thread is tapped or a brass insert fitted Small diameters, load-bearing or frequently opened joints Needs a secondary operation

Design rules for threaded parts

  • Do not run the thread to the edge of the part. Leave a plain section of about 0.8 mm at start and end; otherwise the mold gets a knife-thin steel edge that breaks quickly.
  • Radius the thread root and crest. A sharp root is a notch in plastic and that is where cracks start.
  • Choose coarse pitch over fine pitch; fine plastic threads fill poorly and strip quickly.
  • Interrupted threads make stripping easier and may remove the need for an unscrewing mechanism.
  • Plastic threads and metal screws shrink and expand differently; over long engagements the pitch error accumulates. Keep the engagement no longer than needed.
  • Avoid tapered pipe threads: tightening spreads the plastic boss and cracks it over time.
  • In an unscrewing mold give the part knurls, flats or ribs on the outside so it does not turn with the core.

Volume decides the method

The same threaded part is made with a hand-loaded core for a few thousand pieces a year and with a multi-cavity unscrewing mold for hundreds of thousands. Share the annual volume, the material and the job of the thread (sealing or just holding) at the quotation stage and we will choose the right mold concept together.

Request a Quote

Kalıp ve hassas parça işleriniz için üretim ortağınız

Kokil, plastik enjeksiyon ve alüminyum enjeksiyon kalıpları ile CNC talaşlı imalat tek atölyede. Teknik resminizi gönderin, birlikte değerlendirelim.

Bize Ulaşın
Kasım 16, 2026

Stainless Steel Grades in CNC Machining: 303, 304, 316, 420 and 17-4 PH

Devamını oku
Kasım 16, 2026

CNC İşlemede Paslanmaz Çelik Türleri: 303, 304, 316, 420 ve 17-4 PH

Devamını oku
Tüm haberler ve yazılar