Prototipten seri üretime, kalıptan bitmiş parçaya — İzmir'den. E-posta: info@oskakalip.com Telefon: 0506 462 17 78 WhatsApp Sohbeti Teklif Başlat
Fiyat teklifi alın

Ana Sayfa / English / Manufacturing Method Guide

Manufacturing Method Guide

CNC machining, injection molding, gravity die or die casting? Choose the right method by quantity, material and design maturity.

Türkçe sürüm

The same part can often be made in more than one way; the right method depends on quantity, material, geometry and schedule. A wrong choice turns into either an unnecessary tooling investment or extra labour paid on every part. This guide puts the methods we work with at OSKA side by side and lists the questions to ask before deciding.

Five questionsComparisonBy quantityBy materialPrototype to productionPrototype or production tool?FAQ

Five questions before you decide

  • How many? Today’s need and the annual total; this sets how many parts share the tooling cost.
  • Which material? Plastic, aluminium or steel; the load the part carries and its environment.
  • How complex is the geometry? Thin walls, internal voids, undercuts, free-form surfaces.
  • What tolerance and surface are expected? Which dimensions are truly critical?
  • Schedule and design maturity? If the design is still changing, it may be too early for tooling.

Comparison of methods

Method Material Initial investment Unit cost Where it excels Limit
CNC milling / turning Metals and engineering plastics Almost none High, falls little with quantity Prototypes, low quantities, tight tolerances, thick solid parts Stays expensive as quantity grows; tool access in internal voids
Plastic injection molding Thermoplastics Mold required Very low High volumes, thin-walled complex plastic parts, repeatable appearance A design change means a mold modification
Gravity die (permanent mold) casting Aluminium alloys Moderate tooling Medium Medium volumes, thicker walls, pressure-tight and mechanically sound parts Very thin walls and very fine detail are limited
High-pressure die casting Aluminium alloys High; hot-work steel die Low High volumes, thin walls, high dimensional repeatability High tooling cost; porosity can restrict heat treatment and welding

Choosing by quantity

1101001.00010.000100.000+CNC machiningPrototype toolingProduction toolingGravity die castingDie castingTotal production quantity (approximate, varies with the part)
Quantity ranges in which each method is typically economical. The limits are not fixed; part size and complexity shift them.

The logic is simple: tooled methods carry a large initial cost and a very low part cost, while machining has no initial cost but every part carries the same labour. The quantity at which the two curves cross is the break-even point. Below it CNC wins, above it tooling wins. Break-even can be a few hundred for small simple parts and a few thousand for large complex ones; the soundest approach is to price both routes at the quotation stage.

Choosing by material

Part material Low quantity Medium quantity High quantity
Plastic CNC machining from block Injection molding in a prototype (rapid) tool Injection molding in a production tool
Aluminium CNC machining from block Gravity die casting + machining of key surfaces Die casting + machining of key surfaces
Steel and stainless CNC turning / milling CNC turning / milling in series with fixtures Cast or forged blank + machining, depending on the part

Most castings are not finished on their own: gasket faces, bearing bores and threads are machined to size afterwards. Planning the tool and the machining in one workshop means machining allowances and datums are right from the start.

Three stages from prototype to production

1. PrototypeA few parts to verify the design, usually CNC machined from the real material. The design can still change freely.
2. Pilot runTens or hundreds of parts for assembly and field trials, made by CNC or in a simple prototype tool; data is gathered for the production tool.
3. Series productionThe design is frozen and the production tool is built. Production starts after mold trial and first-sample approval.

Prototype tool or production tool?

Prototype (rapid) tool Production tool
Purpose Verify the design in the real material, produce a pilot run Long-term, uninterrupted series production
Tool material Aluminium or pre-hardened steel Hardened mold steel
Construction Single cavity, simple; undercuts mostly by hand-loaded inserts Can be multi-cavity; slides, lifters and automatic ejection
Cooling and cycle Simple cooling, longer cycle Cooling designed for the shortest cycle
Life Limited number of shots Very high shot counts with maintenance
Time and cost Shorter and lower Longer and higher; lowest cost per part

Frequently Asked Questions

At what quantity does tooling make sense?

There is no single number. The longer the CNC cycle and the simpler the tool, the lower the break-even quantity. Send us your drawing and we can price both routes and look at the break-even point together.

My design is not final yet. Should I start the tool?

We would not recommend it. Every change in steel costs time and money. The safest route is to progress with CNC prototypes until the design matures, verify it with mold flow analysis, and then cut the tool.

Does a machined prototype behave like a molded part?

Not exactly, even in the same material. In a molded part, flow direction, weld lines and internal stresses affect mechanical behaviour. A prototype is reliable for checking dimensions and assembly; for parts near their strength limit a pilot molding run is advisable.

Can a part move from gravity die casting to die casting later?

It can, but the design rules differ: wall thickness, draft and gating all change. If a transition is likely, tell us at the start so the part is designed to suit both.

Request a Quote

Kalıp ve hassas parça işleriniz için üretim ortağınız

Kokil, plastik enjeksiyon ve alüminyum enjeksiyon kalıpları ile CNC talaşlı imalat tek atölyede. Teknik resminizi gönderin, birlikte değerlendirelim.

Bize Ulaşın
Kasım 16, 2026

Stainless Steel Grades in CNC Machining: 303, 304, 316, 420 and 17-4 PH

Devamını oku
Kasım 16, 2026

CNC İşlemede Paslanmaz Çelik Türleri: 303, 304, 316, 420 ve 17-4 PH

Devamını oku
Tüm haberler ve yazılar