Prototipten seri üretime, kalıptan bitmiş parçaya — İzmir'den. E-posta: info@oskakalip.com Telefon: 0506 462 17 78 WhatsApp Sohbeti Teklif Başlat
Fiyat teklifi alın

Ana Sayfa / English / Surface Finishes Guide

Surface Finishes Guide

From blasting to anodising, nitriding to mold polishing: what each finish gives, which materials it suits and how to specify it.

Türkçe sürüm

The surface of a part decides more than its appearance: wear, corrosion, friction, sealing and, in a mold, how the part releases. This guide summarises the surface and finishing processes most often used on machined parts and molds, the materials they suit, and how to call them out on a drawing.

As machinedMechanical finishesCoatingsHeat treatmentMold cavity finishesHow to chooseOn the drawingFAQ

As-machined surface

The fastest and most economical option. The part is delivered as it leaves the machine: tool marks are visible, sharp edges are broken and burrs removed. In standard machining the roughness is typically around Ra 3.2 µm; finishing passes can reach Ra 1.6 and 0.8 µm, but each step adds machining time. Hidden surfaces with no fit function need nothing more.

Mechanical finishes

Process What it gives Suitable materials Watch out for
Bead / grit blasting Even matt surface that hides tool marks; preparation for paint and coating Steel, stainless, aluminium Slightly affects size; mask precise fit surfaces
Vibratory finishing Bulk deburring and edge rounding of small parts Most metals Not for edges that must stay sharp
Brushing Directional decorative grain Stainless, aluminium State the grain direction on visible faces
Grinding Tight tolerance and low roughness; final size on hardened surfaces Steels Leave grinding stock
Polishing Bright, low-roughness surface Steel, stainless, aluminium, brass Labour-intensive; request only where needed

Coatings and conversion processes

Process What it gives Suitable materials Watch out for
Anodising Corrosion and scratch resistance, colour, electrical insulation Aluminium The layer changes dimensions; threads and precise holes can be masked
Hard anodising Thicker, harder layer for wear resistance Aluminium Limited colours; allow for the layer
Powder coating Thick, impact-resistant coloured coating Steel, aluminium Thick layer affects fits; part must withstand oven temperature
Zinc plating Economical corrosion protection for steel Steel Assess hydrogen embrittlement risk on high-strength steels
Nickel and hard chrome plating Wear and corrosion resistance, low friction Steel, copper alloys Include plating thickness in the tolerance
Black oxide Dark surface with almost no dimensional change, light protection Steel Not sufficient outdoors on its own; used oiled
Passivation Strengthens the natural protective layer of stainless steel Stainless steel Does not change appearance or size

Heat treatment and surface hardening

Heat treatment is not a cosmetic process, but it changes surface behaviour more than anything else. Sequence matters: because hardening can cause distortion, precise dimensions are usually produced after heat treatment by grinding, hard milling or sinker EDM.

Process What it gives Typical use
Quench and temper Balance of strength and toughness through the section Shafts, fasteners, mold inserts
Through hardening High hardness and wear resistance Mold cores, cutting and wear parts
Case hardening Hard surface, tough core Gears, pins, impact-loaded parts
Nitriding Hard, low-friction surface with little distortion; resists soldering Ejectors, core pins, die-casting and gravity die surfaces
Stress relieving Reduces machining and welding stresses, stabilises dimensions Large plates, welded frames, rough-machined mold parts

Mold cavity finishes

In plastic injection the part surface is a copy of the cavity surface, so the gloss or texture wanted on the part is applied to the mold steel.

Cavity finish Appearance on the part Note
As machined Light tool marks, non-visible faces Most economical; adequate for internal and technical faces
Stoned / papered (semi-gloss) Even, mark-free but not glossy Standard choice for most technical parts
Mirror polish High gloss, clarity on transparent parts Requires a clean steel suited to polishing
EDM (matt) texture Even matt surface Natural texture of sinker EDM; increase draft in textured areas
Blasted Fine matt surface Makes the surface uniform and hides small marks
Chemical texturing Leather, wood-grain, geometric patterns Extra draft needed according to texture depth

Textured and matt surfaces make ejection harder. The deeper the texture, the more draft is needed; with too little draft the part shows scuffing and stress whitening.

Which finish should I choose?

Need Suggestion
Corrosion and scratch resistance on aluminium Anodising; hard anodising if wear is also involved
Economical rust protection on steel Zinc plating; black oxide and oil where size must not change
Uniform matt look that hides tool marks Blasting; followed by anodising on aluminium
Coloured, impact-resistant outer surface Powder coating
Wear resistance on sliding surfaces Nitriding or hard chrome; hard anodising on aluminium
Tight-tolerance fit surface Grinding; allow for the layer if coating follows
Glossy plastic part Mirror-polished cavity in a suitable steel

How to specify it on the drawing

  • State roughness as Ra or Rz, and only on the surfaces that need it; a tight value on the whole part raises cost for nothing.
  • For coatings give the process, thickness and colour, and say whether dimensions apply before or after coating.
  • Mark surfaces that must not be coated or blasted: threads, fit diameters, contact faces.
  • For heat treatment give the target hardness and, where needed, the case depth.
  • Mark visible surfaces separately so racking and clamping marks are kept away from them.

Frequently Asked Questions

Does coating change the size of the part?

Yes, most coatings add a layer. In anodising part of the layer grows into the surface and part outwards. On precise fits the allowance is built into the machined size, or the surface is masked.

Is a low roughness on every surface better?

No. Low roughness means extra passes, grinding or polishing. Ask for it only where sealing, bearing or appearance requires it.

Which processes are done in your workshop?

Machining, EDM, bench fitting and polishing are done in-house. For processes that need dedicated plants, such as plating and heat treatment, simply tell us your requirement at the quotation stage and the machining sequence is planned around it.

Which materials can be anodised?

Anodising is specific to aluminium. On steel, zinc or nickel plating or black oxide give comparable protection.

Request a Quote

Kalıp ve hassas parça işleriniz için üretim ortağınız

Kokil, plastik enjeksiyon ve alüminyum enjeksiyon kalıpları ile CNC talaşlı imalat tek atölyede. Teknik resminizi gönderin, birlikte değerlendirelim.

Bize Ulaşın
Kasım 16, 2026

Stainless Steel Grades in CNC Machining: 303, 304, 316, 420 and 17-4 PH

Devamını oku
Kasım 16, 2026

CNC İşlemede Paslanmaz Çelik Türleri: 303, 304, 316, 420 ve 17-4 PH

Devamını oku
Tüm haberler ve yazılar