Surface finish is part of the design, not the last step
Corrosion resistance, wear life, appearance and even assembly dimensions all change with the surface finish. When the finish is known from the start, dimensions, material and mold surface are prepared for it; when it is added later, fits bind, threads fill up and colours do not match. This page summarises the most common options for metal parts and for molded plastic parts.
Tell us the finish you need at the quotation stage. We allow for the layer thickness in the dimensions and agree with you which areas have to be masked.
Finishes for metal parts
| Process | Applied to | What it gives | Watch out for |
|---|---|---|---|
| Anodizing | Aluminium | Corrosion resistance, colour options, electrical insulation | The layer grows roughly half inward and half outward; high-silicon casting alloys can come out dark and blotchy |
| Hard anodizing | Aluminium | High surface hardness and wear resistance | The layer is thick and must be allowed for on fits |
| Electroplating (zinc, nickel, chrome) | Steel, brass, zinc alloy | Corrosion protection, hardness, bright appearance | Plating stays thin in blind holes and deep pockets; hydrogen embrittlement risk on high-strength steels |
| Electroless nickel | Steel, aluminium | Uniform thickness even on complex geometry | More expensive than electroplating |
| Powder coating | Steel, aluminium, castings | Thick coloured layer, resistant to impact and UV | Thick layer (about 60–120 µm); threads and fit surfaces must be masked |
| Blasting | All metals | Uniform matt surface, removes burrs and marks, prepares for coating | Can distort thin walls; dimensional faces must be protected |
| Passivation | Stainless steel | Removes free iron from the surface and raises corrosion resistance | Does not change dimensions or appearance |
| Black oxide | Steel | Mild corrosion protection, non-reflective black surface | Practically no dimensional change; not sufficient outdoors on its own |
| Laser marking | Metals and many plastics | Permanent part numbers, logos, data matrix codes | No consumables; high contrast on anodized surfaces |
| Polishing and grinding | All metals | Low roughness for sealing and sliding faces | Labour time rises quickly with surface quality |
How a finish affects dimensions
- Plating and paint add material: shafts grow, holes shrink. For fits such as H7/g6 specify the size before coating.
- Threads fill up in powder coating; mask them or re-cut them afterwards.
- Blasting and polishing remove material and round sharp edges.
- State on the drawing whether a dimension applies before or after coating.
Plastic parts: the part copies the mold surface
The surface of an injection molded part is a copy of the steel surface of the mold. Surface quality on a plastic part is therefore decided when the mold is made.
| Mold surface | How it is produced | Result on the part | Typical use |
|---|---|---|---|
| Mirror polish | Stepwise polishing with diamond paste | Glossy; optical clarity on transparent parts | Lenses, clear covers, glossy decorative parts |
| Semi-gloss | Polishing with fine abrasive paper | Smooth, slightly glossy surface | Visible housings |
| Matt | Stoning | Matt surface that hides marks | Internal and technical parts |
| EDM texture | Die-sink EDM to a VDI 3400 grade | Uniform fine-grained matt surface | Electrical housings, grip areas |
| Chemical texture | Acid etching | Leather, sand or geometric grain | Automotive interior parts, appliance panels |
| Blasted | Glass bead or grit blasting | Satin matt surface | General visible parts |
Draft on textured surfaces
The deeper the texture, the more draft the part needs to leave the mold without scuffing. Rule of thumb: about 1° of extra draft for every 0.025 mm of texture depth. A polished face may work with 0.5–1°, a coarse texture may need 3–5°.
Finishes applied to plastic parts after molding
- Painting: for colour matching and hiding weld lines; materials such as PP and PE need pre-treatment.
- Chrome plating: best on plating-grade ABS and ABS/PC; sharp corners are avoided in the part design.
- Pad and screen printing: for logos and markings.
- Laser marking: permanent and free of consumables; laser additives in the material raise contrast.
- Ultrasonic welding: joins two plastic parts without screws or adhesive.
Treatments for the mold itself
Mold components also receive surface treatments to protect tool life and part quality.
- Nitriding: raises surface hardness; reduces soldering and erosion in aluminium die casting dies and gravity dies.
- PVD coatings (TiN, CrN etc.): reduce wear and galling on cores, ejectors and moving components.
- Hard chrome and nickel plating: protect the cavity against corrosive resins such as PVC.
- Die coating for gravity dies: forms an insulating and release layer between die and molten metal; renewed regularly.
Questions we ask when choosing a finish
- Where will the part work: indoors, outdoors, chemicals, humidity, temperature?
- Which face is visible, and what colour and gloss are expected?
- Which faces are fits, sealing faces or electrical contact faces?
- What is the quantity: rack or barrel processing?
- Is there a standard or customer specification to meet?
Related: Tolerance Guide, Mold Flow Analysis.